Wasp-barcode WLS8600 Product Reference Guide Instrukcja Użytkownika Strona 78
- Strona / 144
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Enter Configuration
Exit and Save Configuration
Ì$+;Î
CODE SELECTION
Ì$-?Î
The Codabar ABC code below uses a fixed start/stop character transmission selection.
Codabar ABC
ÌAD212)Î
no start/stop character equality control but transmission.
Codabar ABC Forced Concatenation
enable Codabar ABC with forced concatenation
ÌAD2321Î
non start/stop character equality control but transmission
CODE LENGTH (optional)
The code length selection is valid for the entire Codabar family
Read the code + 4 numbers for the code length where:
set code length
First 2 digits = minimum code length.
Second 2 digits = maximum code length.
ÌAD*AÎ
The maximum code length is 99 characters.
The minimum code length must always be less than or equal to the maximum.
Examples: 0199 = variable from 1 to 99 digits in the code. 1010 = 10 digit code length only.
START/STOP CHARACTER CASE IN TRANSMISSION
The start/stop character case selections below are valid for the entire Codabar family:
transmit start/stop characters in lower case
ÌADA0_Î
transmit start/stop characters in upper case
ÌADA1cÎ
72
- Reference Manual 1
- CONTENTS 3
- GENERAL VIEW 6
- 1 INTRODUCTION 7
- 2 INSTALLATION 8
- INSTALLATION 9
- CAUTION 9
- 2.2 RS-232 CONNECTION 10
- 2.3 USB 10
- 2.4 IBM USB POS 10
- 2.5 WEDGE CONNECTION 11
- 3 CONFIGURATION 12
- 3.2 SETUP PROCEDURES 13
- Ì$+CP0$-$Î 15
- Ì$+CM2EC0$->Î 15
- Ì$+CM1$-ÈÎ 15
- Ì$+CM0$-ÃÎ 15
- Ì$+CP6$-BÎ 15
- First Start-Up 18
- RS-232 PARAMETERS 21
- BAUD RATE 22
- DATA BITS 23
- STOP BITS 23
- HANDSHAKING 23
- ACK/NACK PROTOCOL 24
- INTER-CHARACTER DELAY 24
- RX TIMEOUT 25
- SERIAL TRIGGER LOCK 25
- USB PARAMETERS 26
- USB-COM 27
- USB-KBD 29
- KEYBOARD NATIONALITY 29
- INTER-CODE DELAY 31
- USB KEYBOARD SPEED 31
- WEDGE PARAMETERS 32
- CAPS LOCK 34
- NUM LOCK 35
- KEYBOARD SETTING 36
- CONTROL CHARACTER EMULATION 38
- PEN EMULATION 39
- OPERATING MODE 40
- MINIMUM OUTPUT PULSE 41
- CONVERSION TO CODE 39 42
- OVERFLOW 42
- OUTPUT LEVEL 43
- IDLE LEVEL 43
- INTER-BLOCK DELAY 43
- DATA FORMAT 44
- CODE IDENTIFIER 46
- CUSTOM CODE IDENTIFIER 46
- four character header 47
- TERMINATOR 48
- SPECIAL KEYS 48
- FIELD ADJUSTMENT 50
- FIELD ADJUSTMENT CHARACTER 51
- CODE LENGTH TX 51
- CHARACTER REPLACEMENT 52
- POWER SAVE 54
- SLEEP STATE 55
- ENTER SLEEP TIMEOUT 55
- READING PARAMETERS 56
- TRIGGER TYPE 57
- TRIGGER SIGNAL 57
- TRIGGER CLICK 57
- TRIGGER-OFF TIMEOUT 58
- FLASH MODE 58
- READS PER CYCLE 58
- SAFETY TIME 59
- BEEPER INTENSITY 59
- BEEPER TONE 60
- BEEPER TYPE 60
- BEEPER LENGTH 60
- GOOD READ SPOT DURATION 61
- AIMING SYSTEM 61
- DECODING PARAMETERS 62
- INK SPREAD 63
- OVERFLOW CONTROL 63
- INTERDIGIT CONTROL 63
- DECODING SAFETY 64
- PUZZLE SOLVER™ 64
- CODE SELECTION 65
- Ì#+AUTOWÎ 66
- EAN/UPC FAMILY 68
- ÌAA8Ad03Î 69
- ÌAA8Ad19Î 69
- 2/5 FAMILY 74
- CODE 39 FAMILY 75
- CODE 128 FAMILY 76
- CODE 93 77
- CODABAR FAMILY 77
- CODE 11 80
- CODE 16K 81
- CODE 49 81
- GS1 DATABAR™ CODES 82
- CONCATENATION 84
- ADVANCED FORMATTING 100
- 4 REFERENCES 102
- 4.1.2 ACK/NACK Protocol 103
- 4.1.3 FIFO 103
- 4.2 PEN PARAMETERS 104
- 4.2.1 Minimum Output Pulse 104
- 4.2.3 Overflow 104
- 4.1.4 RX Timeout 104
- 4.2.5 Inter-Block Delay 105
- 4.3 DATA FORMAT 105
- Enter Configuration 107
- Exit and Save Configuration 107
- REFERENCES 109
- WLS8600 110
- ÌFQ9C2>Î 112
- 4.4 POWER SAVE 115
- 4.4.1 Sleep State 115
- 4.4.2 Enter Sleep Timeout 115
- 4.5 READING PARAMETERS 116
- 4.5.1 Trigger Signal 116
- 4.5.2 Trigger Click 116
- 4.5.3 Trigger-Off Timeout 116
- 4.5.4 Reads per Cycle 116
- 4.5.5 Safety Time 117
- 4.6 DECODING PARAMETERS 117
- 4.6.1 Ink-Spread 117
- 4.6.2 Overflow Control 117
- 4.6.3 Interdigit Control 118
- 4.7 ADVANCED FORMATTING 118
- 4.7.1 Match Conditions 118
- Ì$+$*oÎ 119
- Ì$+$!KÎ 119
- Ì$+$&_Î 119
- Ì$+$0ÂÎ 120
- Ì$+$1$Î 120
- Ì#+CODEÂÎ 120
- Ì$+ZZ0$-*Î 121
- 5 TECHNICAL FEATURES 123
- 5.2 STATUS INDICATORS 124
- 5.3 READING TABLE 125
- SERIAL CONFIGURATION STRINGS 126
- (not for USB-KBD-ALT-MODE) 128
- (IBM AT compatible only) 128
- B CODE IDENTIFIER TABLE 137
- C HEX AND NUMERIC TABLE 140
- Wasp Barcode Technologies 144
- 1400 10th Street 144
- Plano, Texas USA 75074 144
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji